Product Description
|
Permanent-Magnet Variable Frequency Screw Compressor |
|
|
♦ Intelligent Touch-Screen Design |
|
|
♦ Direct-driven |
|
|
♦ Air Cooling |
|
|
♦ Oil Filter |
|
|
♦ Air Filter |
|
|
♦ Stainless Steel |
|
|
♦ Piping Design |
Product features
One shaft-type structure
1. Permanent magnet motor and air-end use the embedded integrated Shaft connecting structure, more compact, 100% transmission Efficiency.
2. No motor bearings, eliminating the motor bearing fault points. Different speeds, permanent magnet
motor with high efficiency, Remarkable energy-saving effect
1. At the rated speed point, permanent magnet motor efficiency is higher Than ordinary motors.
2. Under low motor speed, a permanent magnet motor can still keep high Motor efficiency. If the gas consumption is less, it still keeps extremely High efficiency. Compared with common frequency conversion
3: Motor, the motor efficiency appears obvious gap and the air Compressor has effective energy saving
It has an integrated structure, configuration of high-efficiency Permanent magnet motor, small size, saving space, and easy disassembly. Deploying an efficient permanent magnet variable frequency controller, it Small volume, low noise Can change the speed of the permanent magnet motor according to The exhaust volume, it will achieve lower operation noise than ordinary Ones.
4. Permanent magnet motor has high-performance NdFeB permanent Magnet, 120 º C without loss of excitation, and service life of over 15 Years.
5. Stator coil adopts special inverter corona resistant enameled wire. Insulation performance and longer service life.
6. Realizing soft start, the motor current will not exceed the full load Current during operation, and greatly reduce the impact on network Equipment, with no damage to electrical equipment.OSG-EZV series permanent magnet compressor Stable operation.
Energy-saving advantages:
a. Permanent magnet motor has high-performance NdFeB permanent Magnet, 120 º C without loss of excitation, and service life of over 15 Years.
b. Stator coil adopts special inverter corona resistant enameled wire. Insulation performance and longer service life.
c. Realizing soft start, the motor current will not exceed the full load Current during operation, and greatly reduce the impact on network Equipment, no damage to electrical equipment.OSG-EZV series permanent magnet compressor
Energy-saving advantages:
Condition energy saving
1: The permanent magnet motor remains high efficiency at low speeds, ensuring Obvious energy-saving advantages in small air volumes.
2: Frequency range from 0%-100% (common conversion from 60%-100%)
3: Compared with the fixed speed compressor, energy saving 22%-40%
4: Compared with the common inverter compressor, energy saving 5%-15%
5: System volume fluctuations larger, then energy-saving effect more obvious.
6: Energy saving system of unloading (inverter):
According to the stationary air compressors in gas consumption fluctuation, it has the unloading time, then the air compressor idling but also need 45% of the Electricity, but the permanent-magnet frequency air compressor will control for Inverter, no unloading and no waste. If the air compressor units become larger,
Energy saves more. Save the wasted electric energy by pressure control bandwidth (energy saving):
The fixed compressor must set a minimum control pressure for the 1Barg band (i. E. Air Compressor limits) to avoid the impact on the unit and the power grid. Several Machines must use together with a pressure gradient, more wide pressure, while the OSG permanent-magnet variable-frequency Air compressor series is inverter control, Unlimited stop, no need to set pressure, but a pressure point on the line. With the pressure Of each 0.14Barg bandwidth, the system can save energy by 1%.
Energy saving startup (inverter):
The Air compressor’s starting current is 3-6 times the rated current, the frequent Start will waste a lot of energy, and the frequency conversion type has no frequent Starting and stopping, but a soft start. The maximum current does not exceed the rated working current, no energy waste. At the same time also greatly reduce the impact on network equipment, and no damage to electrical equipment OSG company has obtained a compressor production license(certificate NO: XK06-571-0571), has obtained a quality system certificate, and a general machinery certificate. Product design, Manufacturing processes are strict in accordance with ISO9001: 2008 quality system standards
Permanent magnet motor
Synchronous motor with permanent magnet and frequency
converter without any bearing, elastic coupling, or sealing washer.
Eliminate wear, leakage, and replacement.
Variable speed drive
Variable capacity, controlled cost.
The life cycle cost of the compressor can be reduced by 22% on
average.
State-of-the-art screw components
The material of the rotor is special steel.
Advanced wear-resistant bearings.
The rotating screw comes standard with oversized to achieve the
highest efficiency.
Intelligent controller
Increased reliability: durable keyboard, user-friendly, multilingual
user interface.
Improved ease of use: an intuitive navigation system with main
operation conditions include warning indications, maintenance
scheduling etc.
ZheJiang CHINAMFG Gas Compressor Manufacturing Co.,Ltd. founded in 2005, is a leading high technology of machine and equipment manufacturer integrating the design, R&D, production, sales and service for air compressors & Mining Equipment. Adopting advanced technology, design concept and quality control, and we are able to provide customized products to meet customers’ OEM needs.
Our company has more than 520 employees, including 86 senior technicians and professional engineers. Our technical team provides our customers with professional air system solutions. With the total 15000 square meters of the facility, 4 modern advanced production lines are built up to ensure production capacity to meet customer requirements.
Our company has been awarded the honorary title of “ZheJiang high-tech enterprise” and our products enjoy high honors in the industry. Our company has the ISO9001 certification and was awarded the qualification certificate of equipment through military contracts in 2018.
We offer the following products and services:
1. Screw air compressor
1.1 Oil-free screw air compressor
1.2 Oil-injected air compressor
2. Reciprocating piston air compressor
2.1 Piston air compressor
2.2 Oil-free piston air compressor
2.3 Piston medium & high-pressure air compressor
3. Portable air compressor & Mining Equipment
3.1 Diesel or Electric portable screw air compressor
3.2 Air Pick, Rock Drill, DTH Drilling Rig, Crawler Drilling Rig
4. Air compressor accessories
4.1 CHINAMFG or Adsorption compressed air drier
4.2 Compressed air filter or tank
4.3 Lubrication oil
We have a complete system of after-sales service and quality assurance. The company’s material purchase, inspection, manufacturing, installation, and testing are strictly in accordance with the ISO procedures. which will ensure each compressor has reliable quality and has a complete record to trace if needed.
Q: Do you test all your goods before delivery?
A: Yes, we have 100% test before delivery.
Q: How can we start ordering with your factory?
A: First, leave us an inquiry and advise which item you’re interested in, and then we will contact you within 24 hours. You’re so kind if provide all the detailed information, will be better for us to know exactly what you need.
Q: What is your MOQ?
A: Different products have different MOQs, most are 1 set.
Q: What are your terms of payment?
A: T/T 30% as deposit, and 70% before delivery. We’ll show you the photos of the products and packages.
Q: How about your delivery time?
A: Generally, it will take 90 days after receiving your advance payment. The specific delivery time depends on the items and the quantity of your order.
Q: Do you have a trading company or a real factory?
A: We are a 100% factory; we are located in ZheJiang city, China. /* March 10, 2571 17:59:20 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
| After-sales Service: | Online Support |
|---|---|
| Warranty: | 1 Years |
| Lubrication Style: | Lubricated |
| Cooling System: | Air Cooling |
| Power Source: | AC Power |
| Structure Type: | Closed Type |
| Samples: |
US$ 1500/Piece
1 Piece(Min.Order) | |
|---|
| Customization: |
Available
|
|
|---|
.webp)
Are there special considerations for air compressor installations in remote areas?
Yes, there are several special considerations to take into account when installing air compressors in remote areas. These areas often lack access to infrastructure and services readily available in urban or well-developed regions. Here are some key considerations:
1. Power Source:
Remote areas may have limited or unreliable access to electricity. It is crucial to assess the availability and reliability of the power source for operating the air compressor. In some cases, alternative power sources such as diesel generators or solar panels may need to be considered to ensure a consistent and uninterrupted power supply.
2. Environmental Conditions:
Remote areas can present harsh environmental conditions that can impact the performance and durability of air compressors. Extreme temperatures, high humidity, dust, and corrosive environments may require the selection of air compressors specifically designed to withstand these conditions. Adequate protection, insulation, and ventilation must be considered to prevent damage and ensure optimal operation.
3. Accessibility and Transport:
Transporting air compressors to remote areas may pose logistical challenges. The size, weight, and portability of the equipment should be evaluated to ensure it can be transported efficiently to the installation site. Additionally, the availability of suitable transportation infrastructure, such as roads or air transportation, needs to be considered to facilitate the delivery and installation process.
4. Maintenance and Service:
In remote areas, access to maintenance and service providers may be limited. It is important to consider the availability of trained technicians and spare parts for the specific air compressor model. Adequate planning for routine maintenance, repairs, and troubleshooting should be in place to minimize downtime and ensure the longevity of the equipment.
5. Fuel and Lubricants:
For air compressors that require fuel or lubricants, ensuring a consistent and reliable supply can be challenging in remote areas. It is necessary to assess the availability and accessibility of fuel or lubricant sources and plan for their storage and replenishment. In some cases, alternative or renewable fuel options may need to be considered.
6. Noise and Environmental Impact:
Remote areas are often characterized by their natural beauty and tranquility. Minimizing noise levels and environmental impact should be a consideration when installing air compressors. Selecting models with low noise emissions and implementing appropriate noise reduction measures can help mitigate disturbances to the surrounding environment and wildlife.
7. Communication and Remote Monitoring:
Given the remote location, establishing reliable communication channels and remote monitoring capabilities can be essential for effective operation and maintenance. Remote monitoring systems can provide real-time data on the performance and status of the air compressor, enabling proactive maintenance and troubleshooting.
By addressing these special considerations, air compressor installations in remote areas can be optimized for reliable operation, efficiency, and longevity.
.webp)
How do you maintain proper air quality in compressed air systems?
Maintaining proper air quality in compressed air systems is essential to ensure the reliability and performance of pneumatic equipment and the safety of downstream processes. Here are some key steps to maintain air quality:
1. Air Filtration:
Install appropriate air filters in the compressed air system to remove contaminants such as dust, dirt, oil, and water. Filters are typically placed at various points in the system, including the compressor intake, aftercoolers, and before point-of-use applications. Regularly inspect and replace filters to ensure their effectiveness.
2. Moisture Control:
Excessive moisture in compressed air can cause corrosion, equipment malfunction, and compromised product quality. Use moisture separators or dryers to remove moisture from the compressed air. Refrigerated dryers, desiccant dryers, or membrane dryers are commonly employed to achieve the desired level of dryness.
3. Oil Removal:
If the compressed air system utilizes oil-lubricated compressors, it is essential to incorporate proper oil removal mechanisms. This can include coalescing filters or adsorption filters to remove oil aerosols and vapors from the air. Oil-free compressors eliminate the need for oil removal.
4. Regular Maintenance:
Perform routine maintenance on the compressed air system, including inspections, cleaning, and servicing of equipment. This helps identify and address any potential issues that may affect air quality, such as leaks, clogged filters, or malfunctioning dryers.
5. Air Receiver Tank Maintenance:
Regularly drain and clean the air receiver tank to remove accumulated contaminants, including water and debris. Proper maintenance of the tank helps prevent contamination from being introduced into the compressed air system.
6. Air Quality Testing:
Periodically test the quality of the compressed air using appropriate instruments and methods. This can include measuring particle concentration, oil content, dew point, and microbial contamination. Air quality testing provides valuable information about the effectiveness of the filtration and drying processes and helps ensure compliance with industry standards.
7. Education and Training:
Educate personnel working with compressed air systems about the importance of air quality and the proper procedures for maintaining it. Provide training on the use and maintenance of filtration and drying equipment, as well as awareness of potential contaminants and their impact on downstream processes.
8. Documentation and Record-Keeping:
Maintain accurate records of maintenance activities, including filter replacements, drying system performance, and air quality test results. Documentation helps track the system’s performance over time and provides a reference for troubleshooting or compliance purposes.
By implementing these practices, compressed air systems can maintain proper air quality, minimize equipment damage, and ensure the integrity of processes that rely on compressed air.
.webp)
How do you choose the right size of air compressor for your needs?
Choosing the right size of air compressor is essential to ensure optimal performance and efficiency for your specific needs. Here are some factors to consider when selecting the appropriate size:
1. Air Demand: Determine the air demand requirements of your applications. Calculate the total CFM (Cubic Feet per Minute) needed by considering the air consumption of all the pneumatic tools and equipment that will be operated simultaneously. Choose an air compressor with a CFM rating that meets or exceeds this total demand.
2. Pressure Requirements: Consider the required operating pressure for your applications. Check the PSI (Pounds per Square Inch) rating of the tools and equipment you will be using. Ensure that the air compressor you choose can deliver the necessary pressure consistently.
3. Duty Cycle: Evaluate the duty cycle of the air compressor. The duty cycle represents the percentage of time the compressor can operate within a given time period without overheating or experiencing performance issues. If you require continuous or heavy-duty operation, choose a compressor with a higher duty cycle.
4. Power Source: Determine the available power source at your location. Air compressors can be powered by electricity or gasoline engines. Ensure that the chosen compressor matches the available power supply and consider factors such as voltage, phase, and fuel requirements.
5. Portability: Assess the portability requirements of your applications. If you need to move the air compressor frequently or use it in different locations, consider a portable or wheeled compressor that is easy to transport.
6. Space and Noise Constraints: Consider the available space for installation and the noise restrictions in your working environment. Choose an air compressor that fits within the allocated space and meets any noise regulations or requirements.
7. Future Expansion: Anticipate any potential future expansions or increases in air demand. If you expect your air demand to grow over time, it may be wise to choose a slightly larger compressor to accommodate future needs and avoid the need for premature replacement.
8. Budget: Consider your budgetary constraints. Compare the prices of different air compressor models while ensuring that the chosen compressor meets your specific requirements. Keep in mind that investing in a higher-quality compressor may result in better performance, durability, and long-term cost savings.
By considering these factors and evaluating your specific needs, you can choose the right size of air compressor that will meet your air demand, pressure requirements, and operational preferences, ultimately ensuring efficient and reliable performance.
editor by CX 2024-01-12
China OEM Electric Silent Inverter Screw Air Compressor 30kw 40HP Industrial Air Compressors Factory Spot Direct Sales air compressor lowes
Product Description
HENNI INTERNATIONAL GROUP
Product specifications
| Permanent magnet air compressor | 40A |
| Power | 30KW |
| Exhaust volume | 4.3m³/min |
| length*width*height | 1300mm*1000mm*1290mm |
| Outlet pipe diameter | G 1′ |
| Noise | 69±2 Dda |
| Weight | 420KG |
Product structure
Scope of application
Detail display
high-end material selection
Cooling fan
Cooling fan is mainly to air compressor heat generated by its own cooling
Intake Valve
Automatic adjustment according to the air consumption of the system
Air Filter Assembly device
The inside contains air filter element to filter dust and purify air
Oil and gas separator
High temperature and pressure resistance, using spray paint process
After-sale shoot
/* March 10, 2571 17:59:20 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
| After-sales Service: | Yes |
|---|---|
| Warranty: | 1 Year |
| Lubrication Style: | Lubricated |
| Cooling System: | Air Cooling |
| Power Source: | AC Power |
| Cylinder Position: | Horizontal |
| Customization: |
Available
|
|
|---|
.webp)
What are the energy-saving technologies available for air compressors?
There are several energy-saving technologies available for air compressors that help improve their efficiency and reduce energy consumption. These technologies aim to optimize the operation of air compressors and minimize energy losses. Here are some common energy-saving technologies used:
1. Variable Speed Drive (VSD) Compressors:
VSD compressors are designed to adjust the motor speed according to the compressed air demand. By varying the motor speed, these compressors can match the output to the actual air requirement, resulting in energy savings. VSD compressors are particularly effective in applications with varying air demands, as they can operate at lower speeds during periods of lower demand, reducing energy consumption.
2. Energy-Efficient Motors:
The use of energy-efficient motors in air compressors can contribute to energy savings. High-efficiency motors, such as those with premium efficiency ratings, are designed to minimize energy losses and operate more efficiently than standard motors. By using energy-efficient motors, air compressors can reduce energy consumption and achieve higher overall system efficiency.
3. Heat Recovery Systems:
Air compressors generate a significant amount of heat during operation. Heat recovery systems capture and utilize this wasted heat for other purposes, such as space heating, water heating, or preheating process air or water. By recovering and utilizing the heat, air compressors can provide additional energy savings and improve overall system efficiency.
4. Air Receiver Tanks:
Air receiver tanks are used to store compressed air and provide a buffer during periods of fluctuating demand. By using appropriately sized air receiver tanks, the compressed air system can operate more efficiently. The tanks help reduce the number of starts and stops of the air compressor, allowing it to run at full load for longer periods, which is more energy-efficient than frequent cycling.
5. System Control and Automation:
Implementing advanced control and automation systems can optimize the operation of air compressors. These systems monitor and adjust the compressed air system based on demand, ensuring that only the required amount of air is produced. By maintaining optimal system pressure, minimizing leaks, and reducing unnecessary air production, control and automation systems help achieve energy savings.
6. Leak Detection and Repair:
Air leaks in compressed air systems can lead to significant energy losses. Regular leak detection and repair programs help identify and fix air leaks promptly. By minimizing air leakage, the demand on the air compressor is reduced, resulting in energy savings. Utilizing ultrasonic leak detection devices can help locate and repair leaks more efficiently.
7. System Optimization and Maintenance:
Proper system optimization and routine maintenance are essential for energy savings in air compressors. This includes regular cleaning and replacement of air filters, optimizing air pressure settings, ensuring proper lubrication, and conducting preventive maintenance to keep the system running at peak efficiency.
By implementing these energy-saving technologies and practices, air compressor systems can achieve significant energy efficiency improvements, reduce operational costs, and minimize environmental impact.
How are air compressors utilized in pneumatic tools?
Air compressors play a crucial role in powering and operating pneumatic tools. Here’s a detailed explanation of how air compressors are utilized in pneumatic tools:
Power Source:
Pneumatic tools rely on compressed air as their power source. The air compressor generates and stores compressed air, which is then delivered to the pneumatic tool through a hose or piping system. The compressed air provides the force necessary for the tool to perform various tasks.
Air Pressure Regulation:
Air compressors are equipped with pressure regulation systems to control the output pressure of the compressed air. Different pneumatic tools require different air pressure levels to operate optimally. The air compressor’s pressure regulator allows users to adjust the output pressure according to the specific requirements of the pneumatic tool being used.
Air Volume and Flow:
Air compressors provide a continuous supply of compressed air, ensuring a consistent air volume and flow rate for pneumatic tools. The air volume is typically measured in cubic feet per minute (CFM) and determines the tool’s performance capabilities. Higher CFM ratings indicate that the pneumatic tool can deliver more power and operate at a faster rate.
Tool Actuation:
Pneumatic tools utilize compressed air to actuate their mechanical components. For example, an air-powered impact wrench uses compressed air to drive the tool’s internal hammer mechanism, generating high torque for fastening or loosening bolts and nuts. Similarly, air-powered drills, sanders, nail guns, and spray guns rely on compressed air to power their respective operations.
Versatility:
One of the significant advantages of pneumatic tools is their versatility, and air compressors enable this flexibility. A single air compressor can power a wide range of pneumatic tools, eliminating the need for separate power sources for each tool. This makes pneumatic tools a popular choice in various industries, such as automotive, construction, manufacturing, and woodworking.
Portability:
Air compressors come in different sizes and configurations, offering varying degrees of portability. Smaller portable air compressors are commonly used in applications where mobility is essential, such as construction sites or remote locations. The portability of air compressors allows pneumatic tools to be used in various work environments without the constraints of being tethered to a fixed power source.
Overall, air compressors are integral to the functionality and operation of pneumatic tools. They provide the necessary power, air pressure regulation, and continuous airflow required for pneumatic tools to perform a wide range of tasks efficiently and effectively.
.webp)
What is the purpose of an air compressor?
An air compressor serves the purpose of converting power, typically from an electric motor or an engine, into potential energy stored in compressed air. It achieves this by compressing and pressurizing air, which can then be used for various applications. Here’s a detailed explanation of the purpose of an air compressor:
1. Powering Pneumatic Tools: One of the primary uses of an air compressor is to power pneumatic tools. Compressed air can be used to operate a wide range of tools, such as impact wrenches, nail guns, paint sprayers, sanders, and drills. The compressed air provides the necessary force and energy to drive these tools, making them efficient and versatile.
2. Supplying Clean and Dry Air: Air compressors are often used to supply clean and dry compressed air for various industrial processes. Many manufacturing and production operations require a reliable source of compressed air that is free from moisture, oil, and other contaminants. Air compressors equipped with appropriate filters and dryers can deliver high-quality compressed air for applications such as instrumentation, control systems, and pneumatic machinery.
3. Inflating Tires and Sports Equipment: Air compressors are commonly used for inflating tires, whether it’s for vehicles, bicycles, or sports equipment. They provide a convenient and efficient method for quickly filling tires with the required pressure. Air compressors are also used for inflating sports balls, inflatable toys, and other similar items.
4. Operating HVAC Systems: Air compressors play a crucial role in the operation of heating, ventilation, and air conditioning (HVAC) systems. They provide compressed air for controlling and actuating dampers, valves, and actuators in HVAC systems, enabling precise regulation of air flow and temperature.
5. Assisting in Industrial Processes: Compressed air is utilized in various industrial processes. It can be used for air blow-off applications, cleaning and drying parts, powering air-operated machinery, and controlling pneumatic systems. Air compressors provide a reliable and efficient source of compressed air that can be tailored to meet the specific requirements of different industrial applications.
6. Supporting Scuba Diving and Breathing Systems: In scuba diving and other breathing systems, air compressors are responsible for filling diving tanks and supplying breathable air to divers. These compressors are designed to meet strict safety standards and deliver compressed air that is free from contaminants.
Overall, the purpose of an air compressor is to provide a versatile source of compressed air for powering tools, supplying clean air for various applications, inflating tires and sports equipment, supporting industrial processes, and facilitating breathing systems in specific contexts.
editor by CX 2023-12-21
China OEM 30% Energy Saving Low Noise Industrial VSD Single Rotary Screw Type Air Compressors Price Oil Free Direct Driven Air Compressor 7.5kw 15kw 22kw 37kw 55kw 75kw with Great quality
Product Description
Product Description
The filter system is newly designed for the bipolar compression system, and the reasonable system design is equipped with the top 3 filters to ensure long-term stable operation of the equipment.
Air filter: front cyclone separation plus bipolar air filter with top filter material.
Oil separation core: large filter area plus high-strength metal mesh cover.
Oil Filter: the most extensive filter medium, with low system pressure drop and strong, anti-corrosion shell.
Main Engine Feature
Main Engine
The main engine adopts the design concept of large rotor and low speed, and the spindle speed is 1480. Low noise and vibration.
Two-stage main engine are more energy efficient than single-stage main engine. Under the same working conditions of exhaust volume and exhaust pressure, the energy consumption of the two-stage main engine is reduced by about 15% compared with that of the single-stage main engine. Under the same power consumption and exhaust pressure, the air volume of the two-stage main engine is about 15% larger than that of the single-stage main engine.
Power system:
High-efficiency fully enclosed air-cooled three-phase asynchronous motor, protection grade IP55, insulation grade F, in line with European EFF2 standard. Large starting torque, low noise, more reasonable structure, high efficiency (97%), energy saving, low vibration, reliable performance. Easy installation and maintenance. The front and rear bearings of the motor are the imported SKF bearings, and both are equipped with grease filling ports.
Cooling system:
The design of the super-large cooler makes the heat exchange efficiency higher, the resistance loss is smaller, and the temperature controls and cools fan’s start and stop, which achieves the operation of the constant temperature, so as to achieve the effect of stable operation and energy saving, and make the whole machine especially suitable for areas with large temperature difference and various different Ambient temperature.
Two super-large cooling fans independently control the start and stop of each fan according to the exhaust temperature of the system, which perfectly fits the operation of the air compressor and saves electricity.
Filtration system:
A new filter system is designed for two-stage compression system. The reasonable system design is equipped with the top 3 filter system to ensure the long-term stable operation of the equipment.
Pipeline connection:
Metal hoses are used in oil roads and gas lines. Beautiful and reliable.
Electrical system:
Select the world’s top Schneider Electric components. Reliable work, high protection level, and strong thermal stability.
Specification
| Mode | R90‖-20/8 | R110‖-24/8 | R132‖-28/8 | |
|
Machine Set |
Exhaust volume (m3/min) | 20 | 24 | 28 |
| Exhaust pressure (MPa) | 0.8 | 0.8 | 0.8 | |
| Compression level | two-stage compression | two-stage compression | two-stage compression | |
| Motor power(kw) | 90 | 110 | 132 | |
| Motor speed(rpm) | 1485 | 1485 | 1485 | |
| Energy efficiency rating | Grade I | Grade I | Grade I | |
| Power supply(V/P/Hz) | 380/3/50 | 380/3/50 | 380/3/50 | |
| Start method | Y-△ | Y-△ | Y-△ | |
| Transmission mode | direct connection | direct connection | direct connection | |
| Connection size | DN80 | DN80 | DN80 | |
| Cooling method | air cooling | air cooling | air cooling | |
| Length(mm) | 2682 | 2682 | 3165 | |
| Width(mm) | 1680 | 1680 | 1680 | |
| Height(mm) | 1925 | 1925 | 1945 | |
| Machine weight(kg) | 3350 | 3750 | 3900 | |
| Mode | R160‖-34/8 | R185‖-40/8 | R200‖-43/8 | |
|
Machine Set |
Exhaust volume (m3/min) | 34 | 40 | 43 |
| Exhaust pressure (MPa) | 0.8 | 0.8 | 0.8 | |
| Compression level | two-stage compression | two-stage compression | two-stage compression | |
| Motor power(kw) | 160 | 185 | 200 | |
| Motor speed(rpm) | 1485 | 1485 | 1485 | |
| Energy efficiency rating | Grade I | Grade I | Grade I | |
| Power supply(V/P/Hz) | 380/3/50 | 380/3/50 | 380/3/50 | |
| Start method | Y-△ | Y-△ | Y-△ | |
| Transmission mode | direct connection | direct connection | direct connection | |
| Connection size | DN80 | DN100 | DN100 | |
| Cooling method | air cooling | air cooling | air cooling | |
| Length(mm) | 3165 | 3500 | 3500 | |
| Width(mm) | 1680 | 1860 | 1860 | |
| Height(mm) | 1945 | 2100 | 2100 | |
| Machine weight(kg) | 4200 | 4500 | 4500 | |
| Mode | R220‖-47/8 | R250‖-54/8 | R280‖-60/8 | |
|
Machine Set |
Exhaust volume (m3/min) | 47 | 54 | 60 |
| Exhaust pressure (MPa) | 0.8 | 0.8 | 0.8 | |
| Compression level | two-stage compression | two-stage compression | two-stage compression | |
| Motor power(kw) | 220 | 250 | 280 | |
| Motor power(rpm) | 1485 | 1485 | 1485 | |
| Energy efficiency rating | Grade I | Grade I | Grade I | |
| Power supply (V/P/Hz) | 380/3/50 | 380/3/50 | 380/3/50 | |
| Start method | Y-△ | Y-△ | Y-△ | |
| Transmission mode | direct connection | direct connection | direct connection | |
| Connection size | DN100 | DN125 | DN125 | |
| Cooling method | air cooling | Water cooling | Water cooling | |
| Length(mm) | 3500 | 4240 | 4240 | |
| Width(mm) | 1860 | 2000 | 2000 | |
| Height(mm) | 2100 | 2100 | 2100 | |
| Machine weight(kg) | 4600 | 6500 | 6700 | |
| Mode | R315‖-67.5/8 | |
|
Machine Set |
Exhaust volume (m3/min) | 67.5 |
| Exhaust pressure (MPa) | 0.8 | |
| Compression level | two-stage compression | |
| Motor power(kw) | 315 | |
| Motor speed(rpm) | 1485 | |
| Energy efficiency rating | Grade I | |
| Power supply (V/P/Hz) | 380/3/50 | |
| Start method | Y-△ | |
| Transmission mode | direct connection | |
| Connection size | DN125 | |
| Cooling method | water cooling | |
| Length(mm) | 4240 | |
| Width(mm) | 2000 | |
| Height(mm) | 2100 | |
| Machine weight(kg) | 7200 | |
Specification
| Mode | G7EZ | GV7M | GV15M | GV22M | GV37M | |
|
Machine Set |
Exhaust volume(m³/min) | 1 | 1 | 2.0 | 3.4 | 6.1 |
| Exhaust pressure (MPa) | 0.8 | 0.8 | 0.8 | 0.8 | 0.8 | |
| Compression level | single stage | single stage | single stage | single stage | single stage | |
| Motor power(kW) | 7.5 | 7.5 | 15 | 22 | 37 | |
| Motor speed rmp) | 2900 | 3600 | 3000 | 3000 | 3000 | |
| Energy efficiency rating | Grade III | Grade III | Grade III | Grade III | Grade III | |
| Power supply (V/P/Hz) | 380/3/50 | 380/3/50 | 380/3/50 | 380/3/50 | 380/3/50 | |
| Start method | △ | frequency conversion | frequency conversion | frequency conversion | frequency conversion | |
| Transmission mode | direct connection | direct connection | direct connection | direct connection | direct connection | |
| Outlet size | G3/4″ | G1/2″ | G1″ | G1″ | G1 1/2″ | |
| Cooling method | air cooling | air cooling | air cooling | air cooling | air cooling | |
| Length ×Width x Height (mm) | 710×580× 810 |
710×580× 810 |
1170×690× 940 |
1050×880×1260 | 1200×1000×1430 | |
| Machine weight (kg) | 220 | 220 | 350 | 450 | 550 | |
| After-sales Service: | Online |
|---|---|
| Lubrication Style: | Lubricated |
| Cooling System: | Air Cooling |
| Customization: |
Available
|
|
|---|
.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}
|
Shipping Cost:
Estimated freight per unit. |
about shipping cost and estimated delivery time. |
|---|
| Payment Method: |
|
|---|---|
|
Initial Payment Full Payment |
| Currency: | US$ |
|---|
| Return&refunds: | You can apply for a refund up to 30 days after receipt of the products. |
|---|
.webp)
How are air compressors utilized in the aerospace industry?
Air compressors play a crucial role in various applications within the aerospace industry. They are utilized for a wide range of tasks that require compressed air or gas. Here are some key uses of air compressors in the aerospace industry:
1. Aircraft Systems:
Air compressors are used in aircraft systems to provide compressed air for various functions. They supply compressed air for pneumatic systems, such as landing gear operation, braking systems, wing flap control, and flight control surfaces. Compressed air is also utilized for starting aircraft engines and for cabin pressurization and air conditioning systems.
2. Ground Support Equipment:
Air compressors are employed in ground support equipment used in the aerospace industry. They provide compressed air for tasks such as inflating aircraft tires, operating pneumatic tools for maintenance and repair, and powering air-driven systems for fueling, lubrication, and hydraulic operations.
3. Component Testing:
Air compressors are utilized in component testing within the aerospace industry. They supply compressed air for testing and calibrating various aircraft components, such as valves, actuators, pressure sensors, pneumatic switches, and control systems. Compressed air is used to simulate operating conditions and evaluate the performance and reliability of these components.
4. Airborne Systems:
In certain aircraft, air compressors are employed for specific airborne systems. For example, in military aircraft, air compressors are used for air-to-air refueling systems, where compressed air is utilized to transfer fuel between aircraft in mid-air. Compressed air is also employed in aircraft de-icing systems, where it is used to inflate inflatable de-icing boots on the wing surfaces to remove ice accumulation during flight.
5. Environmental Control Systems:
Air compressors play a critical role in the environmental control systems of aircraft. They supply compressed air for air conditioning, ventilation, and pressurization systems, ensuring a comfortable and controlled environment inside the aircraft cabin. Compressed air is used to cool and circulate air, maintain desired cabin pressure, and control humidity levels.
6. Engine Testing:
In the aerospace industry, air compressors are utilized for engine testing purposes. They provide compressed air for engine test cells, where aircraft engines are tested for performance, efficiency, and durability. Compressed air is used to simulate different operating conditions and loads on the engine, allowing engineers to assess its performance and make necessary adjustments or improvements.
7. Oxygen Systems:
In aircraft, air compressors are involved in the production of medical-grade oxygen for onboard oxygen systems. Compressed air is passed through molecular sieve beds or other oxygen concentrator systems to separate oxygen from other components of air. The generated oxygen is then supplied to the onboard oxygen systems, ensuring a sufficient and continuous supply of breathable oxygen for passengers and crew at high altitudes.
It is important to note that air compressors used in the aerospace industry must meet stringent quality and safety standards. They need to be reliable, efficient, and capable of operating under demanding conditions to ensure the safety and performance of aircraft systems.
.webp)
How does the horsepower of an air compressor affect its capabilities?
The horsepower of an air compressor is a crucial factor that directly impacts its capabilities and performance. Here’s a closer look at how the horsepower rating affects an air compressor:
Power Output:
The horsepower rating of an air compressor indicates its power output or the rate at which it can perform work. Generally, a higher horsepower rating translates to a greater power output, allowing the air compressor to deliver more compressed air per unit of time. This increased power output enables the compressor to operate pneumatic tools and equipment that require higher air pressure or greater airflow.
Air Pressure:
The horsepower of an air compressor is directly related to the air pressure it can generate. Air compressors with higher horsepower ratings have the capacity to produce higher air pressures. This is particularly important when operating tools or machinery that require specific air pressure levels to function optimally. For example, heavy-duty pneumatic tools like jackhammers or impact wrenches may require higher air pressure to deliver the necessary force.
Air Volume:
In addition to air pressure, the horsepower of an air compressor also affects the air volume or airflow it can provide. Higher horsepower compressors can deliver greater volumes of compressed air, measured in cubic feet per minute (CFM). This increased airflow is beneficial when using pneumatic tools that require a continuous supply of compressed air, such as paint sprayers or sandblasters.
Duty Cycle:
The horsepower rating of an air compressor can also influence its duty cycle. The duty cycle refers to the amount of time an air compressor can operate continuously before it needs to rest and cool down. Higher horsepower compressors often have larger and more robust components, allowing them to handle heavier workloads and operate for longer periods without overheating. This is particularly important in demanding applications where continuous and uninterrupted operation is required.
Size and Portability:
It’s worth noting that the horsepower rating can also affect the physical size and portability of an air compressor. Higher horsepower compressors tend to be larger and heavier due to the need for more substantial motors and components to generate the increased power output. This can impact the ease of transportation and maneuverability, especially in portable or mobile applications.
When selecting an air compressor, it is essential to consider the specific requirements of your intended applications. Factors such as desired air pressure, airflow, duty cycle, and portability should be taken into account. It’s important to choose an air compressor with a horsepower rating that aligns with the demands of the tools and equipment you plan to operate, ensuring optimal performance and efficiency.
Consulting the manufacturer’s specifications and guidelines can provide valuable information on how the horsepower rating of an air compressor corresponds to its capabilities and suitability for different tasks.
What are the safety considerations when operating an air compressor?
Operating an air compressor requires careful attention to safety to prevent accidents, injuries, and equipment damage. Here are some important safety considerations to keep in mind:
1. Read the Manual: Before operating an air compressor, thoroughly read and understand the manufacturer’s instruction manual. Familiarize yourself with the specific safety guidelines, recommended operating procedures, and any specific precautions or warnings provided by the manufacturer.
2. Proper Ventilation: Ensure that the area where the air compressor is operated has adequate ventilation. Compressed air can produce high levels of heat and exhaust gases. Good ventilation helps dissipate heat, prevent the buildup of fumes, and maintain a safe working environment.
3. Personal Protective Equipment (PPE): Always wear appropriate personal protective equipment, including safety glasses or goggles, hearing protection, and non-slip footwear. Depending on the task, additional PPE such as gloves, a dust mask, or a face shield may be necessary to protect against specific hazards.
4. Pressure Relief: Air compressors should be equipped with pressure relief valves or devices to prevent overpressurization. Ensure that these safety features are in place and functioning correctly. Regularly inspect and test the pressure relief mechanism to ensure its effectiveness.
5. Secure Connections: Use proper fittings, hoses, and couplings to ensure secure connections between the air compressor, air tools, and accessories. Inspect all connections before operation to avoid leaks or sudden hose disconnections, which can cause injuries or damage.
6. Inspect and Maintain: Regularly inspect the air compressor for any signs of damage, wear, or leaks. Ensure that all components, including hoses, fittings, and safety devices, are in good working condition. Follow the manufacturer’s recommended maintenance schedule to keep the compressor in optimal shape.
7. Electrical Safety: If the air compressor is electric-powered, take appropriate electrical safety precautions. Use grounded outlets and avoid using extension cords unless approved for the compressor’s power requirements. Protect electrical connections from moisture and avoid operating the compressor in wet or damp environments.
8. Safe Start-Up and Shut-Down: Properly start and shut down the air compressor following the manufacturer’s instructions. Ensure that all air valves are closed before starting the compressor and release all pressure before performing maintenance or repairs.
9. Training and Competence: Ensure that operators are adequately trained and competent in using the air compressor and associated tools. Provide training on safe operating procedures, hazard identification, and emergency response protocols.
10. Emergency Preparedness: Have a clear understanding of emergency procedures and how to respond to potential accidents or malfunctions. Know the location of emergency shut-off valves, fire extinguishers, and first aid kits.
By adhering to these safety considerations and implementing proper safety practices, the risk of accidents and injuries associated with operating an air compressor can be significantly reduced. Prioritizing safety promotes a secure and productive working environment.
editor by CX 2023-11-08